february 2016 for high-speed differential signal line, general signal line emc components acm2012e [0805 inch]* * dimensions code jis[eia] common mode filters acm2012e ty p e acm-e series
(2/9) 20160212 / cmf_commercial_signal_acm2012e_en.fm emc components reminders for using these products before using these products, be sure to request the delivery specifications. safety reminders please pay sufficient attention to the warnings for safe designing when using these products. the storage period is less than 6 months. be sure to follow the storage conditions (temperature: 5 to 40c, humidity: 10 to 75 % rh or less). if the storage period elapses, the soldering of the terminal electrodes may deteriorate. do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). before soldering, be sure to preheat components. the preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150c. soldering corrections after mounting should be within the range of the conditions determined in the specifications. if overheated, a short circuit, performance deterioration, or lifespan shortening may occur. when embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. self heating (temperature increase) occurs when the power is turned on, so the tolerance should be sufficient for the set therm al design. carefully lay out the coil for the circuit board design of the non-magnetic shield type. a malfunction may occur due to magnetic interference. use a wrist band to discharge static electricity in your body through the grounding wire. do not expose the products to magnets or magnetic fields. do not use for a purpose outside of the contents regulated in the delivery specifications. the products listed on this catalog are intended for use in general electronic equipment (av equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. the products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. if you intend to use the products in the applications listed below or if you have special requirements exceeding the range or c onditions set forth in the each catalog, please contact us. (1) aerospace/aviation equipment (2) transportation equipment (cars, electric trains, ships, etc.) (3) medical equipment (4) power-generation control equipment (5) atomic energy-related equipment (6) seabed equipment (7) transportation control equipment (8) public information-processing equipment (9) military equipment (10) electric heating apparatus, burning equipment (11) disaster prevention/crime prevention equipment (12) safety equipment (13) other applications that are not considered general-purpose applications when designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securi ng protection circuit/device or providing backup circuits in your equipment. reminders
(3/9) 20160212 / cmf_commercial_signal_acm2012e_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. emc components common mode filters for high-speed differential signal line, general signal line features downsized, low height wound type chip common mode filter that main tains required common mode filter characteristics. impedance for common mode noise can clear 1000 [100mhz], and has excellent emc suppression. differential mode impedance is suppressed, so there is virt ually no affect on high speed signals. application common mode noise countermeasure for high-speed differential signals where influence to the signal is a concern. usb line for pcs and peripheral devices. ieee1394 lines and ethernet lines for pcs, stbs, etc. lcd panel lvds and panel link lines. part number construction operating temperature range, package quantity, product weight the storage temperature range is for after the circuit board is mounted. overview of acm2012e type acm 2012 e - 670 - 2p - t 00 series name lwh dimensions product internal code impedance number of lines packaging style internal code (mm) ( ) at 100mhz 2012 2.01.21.0 e 670 67 2p 2 lines t ?180mm reel 00 general signal line 900 90 01 high-speed differential signal line 121 120 181 180 251 250 391 390 681 680 102 1000 type temperature range reel diameter package quantity individual weight operating temperature c storage temperature c mm (pieces/reel) mg acm2012e C40 to +85 C40 to +85 ?180 2,000 8 product compatible with rohs directive halogen-free compatible with lead-free solders rohs directive compliant product: see the following for more details related to rohs directive compliant products. http://produ ct.tdk.com/en/environment/rohs/ halogen-free: indicates that cl content is less than 900ppm, br content is less than 900ppm, and that the total cl and br conte nt is less than 1500ppm.
(4/9) 20160212 / cmf_commercial_signal_acm2012e_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. emc components acm2012e type recommended reflow profile preheating soldering peak temp. time temp. time temp. time t1 t2 t1 t3 t2 t4 t3 150c 180c 60 to 120s 230c 10 to 30s 245c 5s t3 t1 soaking t2 working t3 t3 t4t4 t5 t2 t1 t: time soldering peak t: temperature
(5/9) 20160212 / cmf_commercial_signal_acm2012e_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. emc components acm2012e type (general signal line) shape & dimensions recommended land pattern circuit diagram 2.00.2 1.2 0.4 0.4 1.20.2 1.00.1 0.3 0.3 0.05 0.5 1 2 4 3 dimensions in mm 1.1 0.75 0.75 0.4 0.4 0.4 dimensions in mm 1 2 4 3 ? no polarity
(6/9) 20160212 / cmf_commercial_signal_acm2012e_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. emc components acm2012e type (general signal line) electrical characteristics characteristics specification table measurement equipment ? equivalent measurement equipment may be used. impedance vs. frequency characteristics measurement equipment ? equivalent measurement equipment may be used. impedance [100mhz dc resistance [1 line] rated voltage insulation resistance rated current part no. ( ) ( )max. (v)max. (m )min. (a)max. 6725% 0.35 50 10 0.50 acm2012e-670-2p-t00 9025% 0.35 50 10 0.33 acm2012e-900-2p-t00 12025% 0.45 50 10 0.30 acm2012e-121-2p-t00 18025% 0.60 50 10 0.25 acm2012e-181-2p-t00 25025% 1.00 50 10 0.20 acm2012e-251-2p-t00 270min. (390typ.) 0.80 50 10 0.30 acm2012e-391-2p-t00 510min. (680typ.) 1.80 50 10 0.17 acm2012e-681-2p-t00 750min. (1000typ.) 2.50 50 10 0.15 acm2012e-102-2p-t00 measurement item product no. manufacturer common mode impedance 4991a keysight technologies dc resistance 4338a keysight technologies insulation resistance 4339a keysight technologies product no. manufacturer 4991a keysight technologies 1 10 100 1000 10000 1000 100 1 10 frequency ( mhz ) impedance ( ) 10000 102 common mode 391 common mode 251 common mode 181 common mode 121 common mode 900 common mode 670 common mode 681 common mode 102 differential mode 681 differential mode 391 differential mode 251 differential mode 181 differential mode 121 differential mode 900 differential mode 670 differential mode
(7/9) 20160212 / cmf_commercial_signal_acm2012e_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. emc components acm2012e type (high-speed differential signal line) shape & dimensions recommended land pattern circuit diagram 2.00.2 1.2 0.4 0.4 1.20.2 1.00.1 0.3 0.3 0.05 0.5 1 2 4 3 dimensions in mm 1.1 0.75 0.75 0.4 0.4 0.4 dimensions in mm 1 2 4 3 ? no polarity
(8/9) 20160212 / cmf_commercial_signal_acm2012e_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. emc components acm2012e type (high-speed differential signal line) electrical characteristics characteristics specification table measurement equipment ? equivalent measurement equipment may be used. impedance vs. frequency characteristics measurement equipment ? equivalent measurement equipment may be used. impedance [100mhz dc resistance [1 line] rated voltage insulation resistance rated current part no. ( ) ( )max. (v)max. (m )min. (a)max. 6725% 0.45 50 10 0.35 acm2012e-670-2p-t01 9025% 0.55 50 10 0.30 acm2012e-900-2p-t01 12025% 0.65 50 10 0.27 ACM2012E-121-2P-T01 measurement item product no. manufacturer common mode impedance 4991a keysight technologies dc resistance 4338a keysight technologies insulation resistance 4339a keysight technologies product no. manufacturer 4991a keysight technologies 1 10 100 1000 10000 1000 100 1 10 frequency ( mhz ) impedance ( ) 10000 121 common mode 900 common mode 670 common mode 900 differential mode 670 differential mode 121 differential mode
(9/9) 20160212 / cmf_commercial_signal_acm2012e_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. emc components acm2012e type packaging style reel dimensions tape dimensions ty p e a w1 w2 n e acm2012e ?1803 9+1/C0 131 60+1/C0 2 typ. dimensions in mm ty p e a b ?d0 e f p0 p1 p2 w k t acm2012e 1.40.1 2.250.1 1.5+0.1/0 1.750.1 3.50.1 4.00.1 4.00.1 2.00.1 8.00.2 1.150.05 0.200.05 ?13.0 0.2 ?21.0 0.8 n e 2.0 0.5 a dimensions in mm 1.0 w2 w1 w f e p0 p1 p2 ?d0 b a t k 160min. taping 440min. drawing direction 500 to 560min. dimensions in mm
|
